All eight clocks on display for the final day of camp.
Wow, took me long enough to post this. The last day of DEEP camp on June 28 and I learned so much from my students that I’ve been completely absorbed in revising the clock design that I haven’t taken time to post the photos of my student’s truly excellent work. Can’t wait for next year.
The video below shows six cardboard clocks running (mostly) all at once. What a lovely sound.
The recent purchases of a large shoe order and a new vacuum turned out to be quite helpful to the class.
Parents and students watch the closing ceremony and show while the clocks wait to be taken home.
The escape wheel reads: “Genius is eternal patience.” – Michelangelo
The escape wheel read: “Play is the highest form of research.” – Albert Einstein
In standard clock construction a clock wheel (aka: gear) is attached to an arbor and the arbor in turn is attached to a pivot. The same methods apply to the Cereal Box Clock except the wheels and arbors are made of paper and the pivots are wood.
Hot glue helps the wheel go round.
Trimming the outer edge of the Hour Wheel.
Using flush jaw wire cutters to cut wheel teeth is methodical yet enjoyable work.
Using a “Japanese” pull saw to cut arbor material. These saw work like butter.
Using a pull saw to cut dowels for pivots. These saws are so sharp that some students could cut through a dowel in one pull!
Assembling pinions is a lot of work and all of the students worked hard. Three eight leaf pinions are required for each clock.
The drilled holes are a little undersized so we must use this very sophisticated pointy stick to increase the diameter.
Five of eight pins inserted.
They don’t have to be straight.
Little smears of hot glue hold the pins in place.
Love the pink hot glue guns.
The first task we tackled in class was to determine which which set of shears worked best for each student to cut double-thick cereal box chipboard. To my delight nearly everyone had strong opinions about the best and worst. I’m so glad I did this as most of the class prefers a pair that I don’t really like and they hate my favorite.
However, I was not surprised to hear their disdain for the #1 pair pictured above. These are your basic cheap-o-always-on-sale craft scissors and they are generally awful for anything other than opening bags of chips.
#2 are an older version of the Fiskars 9911 “Softouch Multi-Purpose” scissors. Even after years of use in my studio these were still a strong favorite.
Though the #3 Fiskars 12-9936 work great for certain things (Lexan for example) I think the blades are just too short to be efficient for the task of cutting cardboard.
I really like the #4 Fiskars 12-7927 “Titanium Nitride Ultimate Craft” scissors. Like the #2 and #3 thease are a “Softouch” spring return set of shears. They feel good in my larger than average hands so I was concerned that they would be too big for the students but they seem to love them.
I thought that they would also love #5, the Fiskars “Premier Quick-Release Multi-Snip” but for reasons I still don’t understand, they hated them. I’m going to leave them around the class room and see if I can catch anyone using them. They are a little smaller than #4 and seem to have a little bit better leverage due to curved blades. Perhaps this curvature is what they don’t like.
#6 was also initially panned by my young reviewers. These very thin blades tend to flex considerably when cutting thick material but they do work well for trimming little bits of the edges. #8 is basically the same set of blades molded into “Softouch” handles.
The #7 Clauss blunt-tip 6″ trimmer was by far the favorite. They are wicked sharp but also fit smaller hands the best. They are a bit strange in that they have very coarse serration close to the pivot which can leave a ragged edge on one side of the cut but most of the students don’t find it comfortable to open the shears that far so it hasn’t been a problem. I ordered two more pair for the class. As for myself, these shears don’t fit my hand very well and I prefer the spring-opening action of the rest.
Items #2-4,6,8 can be purchased at widgetsupply.com (excellent prices and service).
Items #5 and #7 are from McMaster-Carr (items 3512A21 and 3610A12 respectively).
I found item #1 in the bottom of a forgotten box of glitter and pipe cleaners. A few days into the class the handles broke and we threw them away.
I’ve spent perhaps 150 hours working on this in CAD and less than 30 in the studio prototyping. Once all the patterns are printed and stuck to the double thick cereal boxes I think my students will have a shot at building their own in 12 hours of class time.
Materials include cereal box chip board, corrugated cardboard, wood dowel, hand-rolled paper tubes, recycled #1 plastic sheet, and brass grommets. Hot glue and quick set white glue are used for bonding as well as spray adhesive to mount the patterns. Tools include scissors, utility shears, snap blades, flush trim side cutters, sand paper, and a pull saw to cut dowels and paper tube. Class begins on Monday.
I finally have a complete design. There has been a lot of back and fourth between CAD and studio: design an element, build a prototype, redesign, tinker, second prototype, sketch, think about it for a while, third prototype. So even though I have yet to build a complete clock I do have some confidence that it will work.
But first a vacation back to the Fatherland to celebrate my Dad’s 70th Birthday!